Product Series
PRODUCT CATEGORY
-
Shaanxi diaphragm coupling>
-
Shaanxi drum gear coupling>
-
Shaanxi roller chain coupling>
-
Shaanxi plum elastic coupling>
-
Shaanxi star coupling>
-
Shaanxi elastic pin coupling>
-
Shaanxi elastic sleeve pin coupling>
-
Shaanxi tire coupling>
-
Shaanxi serpentine spring coupling>
-
Shaanxi nylon gear coupling>
-
Shaanxi Slider Coupling>
-
Shaanxi clamp housing coupling>
-
Shaanxi rigid coupling>
-
Shaanxi elastic pin gear coupling>
-
Shaanxi coupling accessories>
Industry News
NEWS
- Selection of requirements and grade determination of serpentine spring coupling
- Pay attention to the problems and scope of application when installing the star coupling
- Heat treatment status and disassembly work of star coupling
- The phenomenon that the elastic pin coupling is prone to long processing time
- Talking about the Analysis of the Damage Causes of the Star Coupling
Shaanxi WH type slider coupling
TAG
WH type slider coupling andOldham couplingThe structure is similar, but the difference is that the center cross slider is a square slider, and the center slider is used to slide in the corresponding radial grooves on the end faces of the coupling halves on both sides to complete the coupling of the two halves.This coupling has high noise, low power and fast wear. Generally, it should not be used as long as the rotation speed is very low, such as ball mills.
Specific model of WH slider coupling:
WH1、WH2、WH3、WH4、WH5、WH6、WH7、WH8、WH9、WH10
WH-type slider coupling is a kind of coupling without elastic elements. It is mainly used to allow the coupling of two shafts with radial offset. It consists of a half coupling with grooves on both ends and a square slider in the center. , Use the center slider to slide in the corresponding radial grooves on the end faces of the coupling halves on both sides to complete the coupling of the two halves.
WH type sliding block coupling has high noise, low power and fast wear. Generally, it is not used as much as possible. It is only used when the speed is very low, such as a ball mill.In order to improve the balance, the bolts should be installed between the forward and reverse phases.Jacketed couplings do not have axial, radial and angular compensation performance.
Basic parameters and main dimensions of WH slider coupling
model | Nominal torque Tn(Nm) | Allowable speed [n]r/min | Diameter of shaft hole | Length of shaft hole | D | D1 | B1 | B2 | l | Moment of inertia Kg.m2 | Mass kg | |
d1 d2 | Y | J1 | ||||||||||
L | ||||||||||||
mm | ||||||||||||
WH1 | 16 | 10000 |
10,11 12,14 | 25-32 | 22-27 | 40 | 30 | 52 | 13 | 5 | 0.0007 | 0.6 |
32-42 | 27-30 | |||||||||||
WH2 | 31.5 | 8200 | 12,12,16,(17),18 | 50 | 32 | 56 | 18 | 5 | 0.0038 | 1.5 | ||
WH3 | 63 | 7000 | 16,(17),18,20,22 | 42-52 | 30-38 | 70 | 40 | 60 | 18 | 5 | 0.0063 | 1.8 |
52-62 | 38-44 | |||||||||||
WH4 | 160 | 5700 | 20,22,24,25,28 | 80 | 50 | 64 | 18 | 8 | 0.013 | 2.5 | ||
WH5 | 280 | 4700 | 25,28,30,32,35 | 62-82 | 44-60 | 100 | 70 | 75 | 23 | 10 | 0.045 | 5.8 |
82-112 | 60-84 | |||||||||||
WH6 | 500 | 3800 | 30,32,35,38,40,42,45 | 120 | 80 | 90 | 33 | 15 | 0.12 | 9.5 | ||
WH7 | 900 | 3200 | 40,42,45,48,50,55 | 112 | 84 | 150 | 100 | 120 | 38 | 25 | 0.43 | 25 |
112-142 | 84-107 | |||||||||||
WH8 | 1800 | 2400 | 50,55,60,63,65,70 | 190 | 120 | 150 | 48 | 25 | 1.98 | 55 | ||
WH9 | 3550 | 1800 | 65,70,75,80,85 | 172-212 | 132-167 | 330 | 190 | 180 | 58 | 40 | 4.9 | 85 |
172-212 | 132-167 | |||||||||||
WH10 | 5000 | 1500 | 80,85,90,95,100 | 330 | 190 | 180 | 58 | 40 | 7.5 | 120 |