Product Series
PRODUCT CATEGORY
-
Diaphragm coupling>
-
Drum type gear coupling>
-
Roller chain coupling>
-
Plum elastic coupling>
-
Star coupling>
-
Elastic pin coupling>
-
Elastic sleeve pin coupling>
-
Tire coupling>
-
Serpentine spring coupling>
-
Nylon gear coupling>
-
Slider coupling>
-
Clamping coupling>
-
Rigid coupling>
-
Elastic pin gear coupling>
-
Coupling accessories>
Industry News
NEWS
- Selection of requirements and grade determination of serpentine spring coupling
- Pay attention to the problems and scope of application when installing the star coupling
- Heat treatment status and disassembly work of star coupling
- The phenomenon that the elastic pin coupling is prone to long processing time
- Talking about the Analysis of the Damage Causes of the Star Coupling
JM type elastic diaphragm coupling
TAG
■JM型弹性膜片联轴器结构特性:
●按传递扭矩及挠性大小分四、六、八等分连杆形式。
●承载能力大,适用范围大,寿命长,传递公称转矩为25~1000000N.m。
●工作温度-20~+250ºC,且无需润滑,可在腐蚀介质中工作。
●与齿式联轴器比,结构简单,易加工、维修,振动小,无噪声,适合高转速下使用。
●装拆、检查方便,拆卸时传动系统主从动部分可不轴向移位脱开。
●广泛应用于冶金、轧钢、矿山、化工、造船、泵、风机等行业。
●型式与标记,轴孔和键槽型式按GB/T3852的规定,轴孔长度L推荐值。
安装JM型Elastic diaphragm couplingThe 8 points to note are as follows:
①. The product with diaphragm has edges and may cause injury. It is recommended to wear thick gloves when installing.
②.请在联轴器周边安装保护罩等装置。
③. When the shaft center deviation exceeds the allowable value during installation, the coupling may be deformed and cause damage or shorten the service life.
④.联轴器的容许轴心偏差包括径向,角向,轴向偏差。安装时,请进行调整轴心偏差在对应的产品目录的容许值范围内。
⑤.当多种偏差同时出现时,相应的容许值要减半。
⑥. In order to prolong the service life of the coupling, it is recommended to set the axis deviation within 1/3 of the allowable value.
⑦. Tighten the screws after inserting the mounting shaft, otherwise the coupling will be deformed. When tightening the screws, please use a torque wrench, do not use screws other than accessories for installation.
⑧.如果在运转过程中出现异常声音,请立即停止运行,并对安装精度,螺丝松动情况等分别进行检查.建议安装调试完毕后在螺丝外表面涂粘接剂,增加保护性能。
technical parameter:
型 号 | 公称 转矩 N.m | 瞬时较大转矩 N.m | 较大转速 r/min | Axle hole diameter d1, d2 | Length of shaft hole mm | D mm | A mm | 重量 mm | 转动 惯量 kg·m2 | ||
J1型 | Y type | L (推荐) | |||||||||
L | L | ||||||||||
JM1 | 40 | 63 | 10700 | 14 | 27 | 32 | 35 | 80 | 8±0.2 | 0.9 | 0.0005 |
16, 18, 19 | 30 | 42 | |||||||||
20, 22, 24 | 38 | 52 | |||||||||
25, 28 | 44 | 62 | |||||||||
JM2 | 63 | 100 | 9300 | 20, 22, 24 | 38 | 52 | 40 | 92 | 1.4 | 0.0011 | |
25, 28 | 44 | 62 | |||||||||
30-32-35 | 60 | 82 | |||||||||
JM3 | 100 | 200 | 8400 | 25, 28 | 44 | 62 | 45 | 102 | 2.1 | 0.002 | |
30-32-35 | 60 | 82 | |||||||||
40, 42, 45 | 84 | 112 | |||||||||
JM4 | 250 | 400 | 6700 | 30-32-35 | 60 | 82 | 55 | 128 | 11±0.3 | 4.2 | 0.006 |
40, 42, 45, 48, 50, 55 | 84 | 112 | |||||||||
JM5 | 500 | 800 | 5900 | 35, 38 | 60 | 82 | 65 | 145 | 6.4 | 0.012 | |
40, 42, 45, 48, 50, 55, 56 | 84 | 112 | |||||||||
60, 63, 65 | 107 | 142 | |||||||||
JM6 | 800 | 1250 | 5100 | 40, 42, 45, 48, 50, 55, 56 | 84 | 112 | 75 | 168 | 14±0.3 | 9.6 | 0.024 |
60, 63, 65, 70, 71, 75 | 107 | 142 | |||||||||
JM7 | 1000 | 2000 | 4750 | 45, 48, 50, 55, 56 | 84 | 112 | 80 | 180 | 15±0.4 | 12.5 | 0.0365 |
60, 63, 65, 70, 71, 75 | 107 | 142 | |||||||||
80 | 132 | 172 | |||||||||
JM8 | 1600 | 3150 | 4300 | 50, 55, 56 | 84 | 112 | 200 | 15.5 | 0.057 | ||
60, 63, 65, 70, 71, 75 | 107 | 142 | |||||||||
80, 85 | 132 | 172 | |||||||||
JM9 | 2500 | 4000 | 4200 | 55, 56 | 84 | 112 | 205 | 20±0.4 | 16.5 | 0.065 | |
60, 63, 65, 70, 71, 75 | 107 | 142 | |||||||||
80, 85 | 132 | 172 | |||||||||
JM10 | 3150 | 5000 | 4000 | 55, 56 | 84 | 112 | 90 | 215 | 19.5 | 0.083 | |
60, 63, 65, 70, 71, 75 | 107 | 142 | |||||||||
80, 85, 90 | 132 | 172 | |||||||||
JM11 | 4000 | 6300 | 3650 | 60, 63, 65, 70, 71, 75 | 107 | 142 | 100 | 235 | 23±0.5 | 25 | 0.131 |
80-85-90 | 132 | 172 | |||||||||
JM12 | 5000 | 8000 | 3400 | 60, 63, 65, 70, 71, 75 | 107 | 142 | 250 | 30 | 0.174 | ||
80-85-90 | 132 | 172 | |||||||||
100 | 167 | 212 | |||||||||
JM13 | 6300 | 10000 | 3200 | 63, 65, 70, 71, 75 | 107 | 142 | 110 | 210 | 36 | 0.239 | |
80-85-90 | 132 | 172 | |||||||||
100, 110 | 167 | 212 | |||||||||
JM14 | 8000 | 12500 | 2850 | 65-70-71 | 107 | 142 | 115 | 300 | 27±0.6 | 45 | 0.38 |
80-85-90 | 132 | 172 | |||||||||
100, 110 | 167 | 212 | |||||||||
JM15 | 10000 | 16000 | 2700 | 70, 71, 75 | 107 | 142 | 125 | 320 | 55 | 0.5 | |
80-85-90 | 132 | 172 | |||||||||
100-110-120 | 167 | 212 |